Random MS3 Chat Thread

[Mr Wilson]

lol shes all good, will be putting in the following order in within a week or so..
EGR delete kit
catch can
grimspeed ebcs
snow performance meth kit stage 2
CP-e injector seals

:)

Cough, cough, check buy sell.

[mikey32235]

Cough, cough, check buy sell.

LOL pm'd

[fywdyl]

http://ct.fra.bz/ol/fz/sw/i57/2/4/20/frabz-SPENDS-OVER-1000-ON-NEW-TURBO-CANT-AFFORD-20-BLOCKOFF-PLATE-a740b9.jpg

[loki]

How will you afford the gas once the new turbo goes in?


Gonna park the car for 2 years to save up? LoL

[breakfasteatre]

http://ct.fra.bz/ol/fz/sw/i57/2/4/20/frabz-SPENDS-OVER-1000-ON-NEW-TURBO-CANT-AFFORD-20-BLOCKOFF-PLATE-a740b9.jpg

*dad spends over 1000 on new turbo..

if dad isnt forking out anymore money, what u gunna do brudder

btw, done a compression test?

[mikey32235]

hahaha good one guys... but everything has been paid out of my own pocket. including the car. yes i did a compression test before installing my FMIC, but im gonna do one again just to make sure everything checks out ok.

[Snotrocket]

hahaha good one guys... but everything has been paid out of my own pocket. including the car. yes i did a compression test before installing my FMIC, but im gonna do one again just to make sure everything checks out ok.

What were the results of the compression test.

[mikey32235]

What were the results of the compression test.

if i can remember correctly they were around 185... cant remember exactly

what should they be around, just for me to know for when i do it again

[Snotrocket]

if i can remember correctly they were around 185... cant remember exactly

what should they be around, just for me to know for when i do it again

http://www.mazdaspeedforums.org/forum/f10/disi-compression-results-43395/

[mikey32235]

i see it should be around 160, from what i remember, my mechanic confirmed my motor was good. will check monday and post results then

[Snotrocket]

i see it should be around 160, from what i remember, my mechanic confirmed my motor was good. will check monday and post results then

In before http://img.tapatalk.com/d/13/04/21/9asa2a5u.jpg

[mikey32235]

looks like a bomb went off. cant wait to see the results of your build after man.

[breakfasteatre]

Let me guess, you bought the car from your mechanic. I'll come over and do the xompression test for you. I am very curious

[Snotrocket]

Let me guess, you bought the car from your mechanic. I'll come over and do the xompression test for you. I am very curious

We all are.

[mikey32235]

lol no actually i didnt. but good guess ;)

[breakfasteatre]

I wouldn't trust any ***in mechanic. I have a compression tester. Let me do it for you before you melt cylinder threes piston. Trust us.

[mikey32235]

sounds good. but i can do it myself too i know what im doing bro. ill post results when i do it before installing anything.

[Fack_Dude]

sounds good. but i can do it myself too i know what im doing bro. ill post results when i do it before installing anything.

Hey mike. Let these guys help you with this task. They know what they are doing.

[mikey32235]

yeah that sounds good. once i get the turbo, well figure out a time and place to do this.

[fywdyl]

yeah that sounds good. once i get the turbo, well figure out a time and place to do this.

It's a preventative measure. It really should be done before you get the turbo.

[mikey32235]

where should this take place

[Fack_Dude]

where should this take place

Your house. Tell mom and pops to pick up some beers and pizzas. Lol

[mikey32235]

Your house. Tell mom and pops to pick up some beers and pizzas. Lol

lol sounds good. ill send a limo.

[loki]

No limo needed

[Snotrocket]

I'm going to guess 180-150-150-180

[loki]

I'm going to guess 180-150-150-180

That's just mean

:chuckle

[mikey32235]

im gonna guess 180-180-180-180 ;)

[pwdunmore]

Is the only place to mount the Snow performance Meth tank under the bumper?

I saw some pics of some in the engine bay but believe they are the smaller kind... I just don't want it to be a pain in the butt to fill up. Might sell/trade the SP for just that reason alone... fack...

[breakfasteatre]

im gonna guess 180-180-180-180 ;)

im gonna guess (im psychic) 170-170-150-170

good compression is about as much truth as your signature


this is an offer to help you out, i will come to your place and do a compression test. I live in richmond hill as well.

we have money riding on how bad the numbers are

[loki]

Is the only place to mount the Snow performance Meth tank under the bumper?

I saw some pics of some in the engine bay but believe they are the smaller kind... I just don't want it to be a pain in the butt to fill up. Might sell/trade the SP for just that reason alone... fack...

O.M.G.

[breakfasteatre]

Is the only place to mount the Snow performance Meth tank under the bumper?

I saw some pics of some in the engine bay but believe they are the smaller kind... I just don't want it to be a pain in the butt to fill up. Might sell/trade the SP for just that reason alone... fack...

mount it wherever you want, as long as you have enough line, and you can mount the pump relatively close.

or you could just tap the stock tank

[boyracer]

im gonna guess (im psychic) 170-170-150-170

good compression is about as much truth as your signature


this is an offer to help you out, i will come to your place and do a compression test. I live in richmond hill as well.

we have money riding on how bad the numbers are

lol

[pwdunmore]

O.M.G.

Just for clarification I meant the SP tank... not the whole thing lol...

[loki]

Just for clarification I meant the SP tank... not the whole thing lol...

We know what you meant

[breakfasteatre]

my nators:

http://www.mazdaspeedforums.org/foru...2/#post2022035

The warm weather is upon us and I'm sure many of you have parts that you have been waiting to install.

I have charcoal BBQ, ill have some hotdogs or something.


I'd like to see some new faces, as well as the usuals.


PM me for address. I have spots for 2 in the driveway and then a small parking lot directly in front of the house.

AS WELL: Snotrocket; is dropping in his built motor this weekend in peterborough. PM him and drop by to lend a hand


just an FYI: if you are new and have parts to install, you do the install yourself. We will be there for guidance and to lend a hand, not do all the work for you.

Can we unite under Nator Canada, ffs

[Snotrocket]

my nators:

http://www.mazdaspeedforums.org/foru...2/#post2022035

The warm weather is upon us and I'm sure many of you have parts that you have been waiting to install.

I have charcoal BBQ, ill have some hotdogs or something.


I'd like to see some new faces, as well as the usuals.


PM me for address. I have spots for 2 in the driveway and then a small parking lot directly in front of the house.

AS WELL: Snotrocket; is dropping in his built motor this weekend in peterborough. PM him and drop by to lend a hand


just an FYI: if you are new and have parts to install, you do the install yourself. We will be there for guidance and to lend a hand, not do all the work for you.

Can we unite under Nator Canada, ffs

Thanks Alex. Build starts Friday.

[Fobio]

Prosport order is placed. I hope they ship on Mon or Tues. Glenn@Prosport are throwing in lanyards for those who ordered. I also asked for air freshners...Alex, I know you wanted one, I should have 2 for you, cuz you smell like vagina...lol... ;)

EDIT: I mean your car smells like there are always vaginas in it...lol...

[loki]

Prosport order is placed. I hope they ship on Mon or Tues. Glenn@Prosport are throwing in lanyards for those who ordered. I also asked for air freshners...Alex, I know you wanted one, I should have 2 for you, cuz you smell like vagina...lol... ;)

Yes

[breakfasteatre]

http://ontario.kijiji.ca/c-cars-vehicles-cars-trucks-2008-Mazda-MAZDASPEED3-Hatchback-W0QQAdIdZ478355861 for prospective buyers, do a compression test first. Not sure whose car this is but better safe than sorry

[Fack_Dude]

http://ontario.kijiji.ca/c-cars-vehicles-cars-trucks-2008-Mazda-MAZDASPEED3-Hatchback-W0QQAdIdZ478355861 for prospective buyers, do a compression test first. Not sure whose car this is but better safe than sorry

You know who bro. ;)

[loki]

def do compression test

[breakfasteatre]

Speaking of compression tests, mikey where you at!?

[Snotrocket]

Speaking of compression tests, mikey where you at!?

He's been on, I've seen him lurking. I think he's probably upset we were bang on with the compression results and now is trying to screw someone else into paying $14,000 for it.....

[breakfasteatre]

He's been on, I've seen him lurking. I think he's probably upset we were bang on with the compression results and now is trying to screw someone else into paying $14,000 for it.....

explain? he is selling his car now?

[boyracer]

explain? he is selling his car now?

lol, the one on kijiji is his.

[rzapata]

Damn. Compression must be that bad...

[breakfasteatre]

Currently Active Users
There are currently 220 users online. 66 members and 154 guests
Most users ever online was 473, 11-04-2012 at 11:54 PM.
breakfasteatre, -RJ3-, 6strings, AlexNguyen, andi_alb, asyed, a_ahmed, baymoe, Bloomer, Boris, chan7, copycat10, Cudgel, dambay, DDUKI, ds08tf, Dynames, floridingmazda, Fobio, Forzer, Gareth232, geobur, greyseason, Hyperion, JaYson, JD@WhitbyMazda, jonjon72, Kappa, KidRambo, leungalv, loosecannon, Low&Slow3, manda_belle, mazdank, mazdathree3, metacore, mikey32235, mpfive, MRT_MS3, Pacman, png, pwdunmore, rl777, Rob23, rsquared, runner2k, S.F.W., Shen, ShibaYuki, Shinglez, Snotrocket, SomeGuy, somers0002, SupermanRitz, Thrizzl3, Tizmee24, trulankan, Turok, turtlejai11, vip3r87, vladimirb91, yuvannr, zmz3


hey man, why you selling?

[boyracer]

lol

[loki]

Thought Alex was trolling...

Turns out he's genuinely confused

[mikey32235]

Thought Alex was trolling...

Turns out he's genuinely confused

... ;)

[breakfasteatre]

i had missed this:


i see it should be around 160, from what i remember, my mechanic confirmed my motor was good. will check monday and post results then

[mikey32235]

results were much better than that.. not really the reason why im selling.

[Kiyomi]

results were much better than that.. not really the reason why im selling.

just curious, what were the results?

[boyracer]

just curious, what were the results?

We're all curious. I just don't know if we'll get an honest answer if we get one at all.

[breakfasteatre]

results were much better than that.. not really the reason why im selling.

Internet butt hurtz is not a real reason to sell.

I hope it's another dumbass knowitall kid who picks it up and not an actual enthusiast.

the car is hurting and selling it without disclosing the real compression numbers is ****ing slimey. Hopefully prospective buyers will come on and ask about the car, and unlike vlads old red speed, TAKE OUR ADVICE AND REFRAIN FROM BUYING IT

[peterm15]

Hopefully prospective buyers will come on and ask about the car, and unlike vlads old red speed, TAKE OUR ADVICE AND REFRAIN FROM BUYING IT

Damn. I was interested to. :chuckle

[rzapata]

I guess we'll never know now.

[mikey32235]

Internet butt hurtz is not a real reason to sell.

I hope it's another dumbass knowitall kid who picks it up and not an actual enthusiast.

the car is hurting and selling it without disclosing the real compression numbers is ****ing slimey. Hopefully prospective buyers will come on and ask about the car, and unlike vlads old red speed, TAKE OUR ADVICE AND REFRAIN FROM BUYING IT

im a dumbass? cool :)...some people are such c*cksuckers these days, its hilarious.

[pwdunmore]

im a dumbass? cool :)...some people are such c*cksuckers these days, its hilarious.

Hey Mikey no need for that... I think it would be better to tell the reason for selling even if its something as vague as life problems. And just leave it like that. Sad to see the car for sale after all the work that has gone into it.

[Snotrocket]

Karma will catch up to you Mike..... The car gods will treat you very poorly if you don't disclose the fact that cylinder 3 is compressionly challenged to any potential buyer.

[breakfasteatre]

Karma will catch up to you Mike..... The car gods will treat you very poorly if you don't disclose the fact that cylinder 3 is compressionly challenged to any potential buyer.

its 2 and 3

[Snotrocket]

I hope my prosport order comes soon, I can't start my car for the first time without my lanyard :)

[J_Logik]

Hey Gents, a quick inquiry. I checked the sponsor section and didn't see anything, where is the best place to get a suspension alignment done? I plan on getting some coilovers installed and want to make sure the shop is comfortable with moderately to significantly lowered cars!!

Thanks in Advance,

Hey breakfasteatre, you offering anymore compression tests for Sunday? I'll take one!!:P

[Kiyomi]

Hey Gents, a quick inquiry. I checked the sponsor section and didn't see anything, where is the best place to get a suspension alignment done? I plan on getting some coilovers installed and want to make sure the shop is comfortable with moderately to significantly lowered cars!!

Thanks in Advance,


Limitless Auto.

[Mr Wilson]

Altech does lowered cars as well (Kipling south of Dundas).

[breakfasteatre]

Hey Gents, a quick inquiry. I checked the sponsor section and didn't see anything, where is the best place to get a suspension alignment done? I plan on getting some coilovers installed and want to make sure the shop is comfortable with moderately to significantly lowered cars!!

Thanks in Advance,

Hey breakfasteatre, you offering anymore compression tests for Sunday? I'll take one!!:P


J, you coming?

I have the tester, we might as well do as many as we can :)

[zzz3]

Altech does lowered cars as well (Kipling south of Dundas).
+1

Make sure to ask for pat (and alignment print out beforehand). $60 cash.

[Booostin]

Internet butt hurtz is not a real reason to sell.

I hope it's another dumbass knowitall kid who picks it up and not an actual enthusiast.

the car is hurting and selling it without disclosing the real compression numbers is ****ing slimey. Hopefully prospective buyers will come on and ask about the car, and unlike vlads old red speed, TAKE OUR ADVICE AND REFRAIN FROM BUYING IT

It was too late for me because I already signed the contract lol. I wish I knew that before but hey... live and learn. BTW the car is for sale with a brand new engine and turbo ;)

[loki]

It was too late for me because I already signed the contract lol. I wish I knew that before but hey... live and learn. BTW the car is for sale with a brand new engine and turbo ;)

Do you have a cp-e triple pod? I'm looking for one

[Booostin]

Do you have a cp-e triple pod? I'm looking for one

I sold it to Mikey lol but seeing as his car is for sale....

[loki]

I sold it to Mikey lol but seeing as his car is for sale....

Will pm him

[thanu31]

J, you coming?

I have the tester, we might as well do as many as we can :)

Hey
I wouldn't mind getting a comp test done. How would I go about getting it done with you? Please pm me details on cost, etc

Thanks

[breakfasteatre]

Sunday is a nator install day. Ie you bring the parts and install them yourself, or in this case use my tester and do the compression test yourself. The collective will be there to help and provide guidance, not do it for you. I am not a mechanic and cars are a hobby and install days are not get shit installed for a price day. Do the research and for the most part know how to do it. Help is there *if needed.

This is more of a general statement but because you mentioned cost I am replying to your post

[Nino]

PM me if anyone has an aftermarket catback for sale!!

[Booostin]

PM me if anyone has an aftermarket catback for sale!!

For MS3?

[Nino]

Yes Gen1 specifically

[Booostin]

I think I still have my cnt exhaust but it doesn't have the muffler section. It is straight through.

[Nino]

So its not the whole piece?


http://www.mazdaspeedstore.com/mazdaspeed/CNT-Racing-3-Cat-Back-Exhaust-Mazdaspeed3-2007-2009-p-425.html#

Which part would it be missing?

If you have the whole catbackmill come to sauga and buy it today.

[Booostin]

That is the one I bought but let me check and see which parts I have because I know I removed the muffler. Ill let you know soon.

[Nino]

Thanks, and by muffler do you mean resonator or cat? It doesnt seem to come with a muffler. Either way as long as it maintains a 3" diameter im happy.

[J_Logik]

J, you coming?

I have the tester, we might as well do as many as we can :)

A, I'm trying to stop by, but I have somewhere to be until early afternoon (it is in the north end of the city so I should be able to). Can you PM the address and I'll do my best to make it.

Oh and to the others who responded regarding the alignment, Thanks. Between that and the shop feedback thread, I got the info I needed and have an appointment booked for next week.

[pwdunmore]

Getting a custom exhaust on friday :headbang If I am free sunday I will swing by Nator and help out where I can since I will have no parts to install... need to wait for the JBR order and pick up my meth from fobio...

[fywdyl]

I have to change my wiper blade insert. That is my install for Sunday.

[pwdunmore]

I have to change my wiper blade insert. That is my install for Sunday.
Need help? lol... I'll bring my power tools

[robl]

Hi All,

Installed Autotech internals and put a stage 2 map yesterday...I'm in LOVE!!!
Just thought I'd share...

Thanks,
Rob.

[Snotrocket]

Hi All,

Installed Autotech internals and put a stage 2 map yesterday...I'm in LOVE!!!
Just thought I'd share...

Thanks,
Rob.

Mods?

[robl]

Corksport SRI & TIP, Cobb BPV, Racing Beat CBE.
Now I NEEEED a downpipe!
;-)

Thanks,
Rob.



Mods?

[robl]

Need an upgraded IC too...
Thanks,
Rob

Corksport SRI & TIP, Cobb BPV, Racing Beat CBE.
Now I NEEEED a downpipe!
;-)

Thanks,
Rob.

[Snotrocket]

Corksport SRI & TIP, Cobb BPV, Racing Beat CBE.
Now I NEEEED a downpipe!
;-)

Thanks,
Rob.

Have you deleted any cats?

Thanks,
Mike

[Nino]

Hey rob. Im running the exact mods as you except I have downpipeback exhaust. Just installed the autotech internals but I haven't switched to stage 2.

Hows the car running? My CPe DP wont fit with my DP back exhaust so im buying a catback exhaust. Im very eager to get my DP and FMIC soni can run stage 2.. A local caliber srt4 kept pulling on me, I could only catch up through turns.

[Snotrocket]

Hi All,

Installed Autotech internals and put a stage 2 map yesterday...I'm in LOVE!!!
Just thought I'd share...

Thanks,
Rob.

I believe at least one deleted cat is required to run stage two....

http://velocityfactor.wordpress.com/2011/09/02/2007-2011-mazdaspeed-3-performance-upgrade-guide-stage-2/

Thanks,

Shawn

[Mr Wilson]

Nino, you running stock cat back? It will work with the cp-e downpipe.

[Nino]

Hey, Im running a 3" downpipe back exhaust made by Vibrant. It replaces the stock cat. The cpe also replaces that lower cat so i wont bolt up with my exhaust.

Just got off the phone with garage16 I was about to drive down to pick up an HKS CBE but they had one left and its on hold :(

[robl]

Hi Shawn,

Sorry, I suppose that I should have indicated that I'm running the stage 2 OTS map from COBB based on their AP website based on my mods.
Car is running great with it so I'm happy...for now ;-)

Thanks,
Rob.


I believe at least one deleted cat is required to run stage two....

http://velocityfactor.wordpress.com/2011/09/02/2007-2011-mazdaspeed-3-performance-upgrade-guide-stage-2/

Thanks,

Shawn

[Snotrocket]

Hi Shawn,

Sorry, I suppose that I should have indicated that I'm running the stage 2 OTS map from COBB based on their AP website based on my mods.
Car is running great with it so I'm happy...for now ;-)

Thanks,
Rob.

Did it not say that a cat had to be deleted or be running a high flow cat?

[loki]

Hi Shawn,

Sorry, I suppose that I should have indicated that I'm running the stage 2 OTS map from COBB based on their AP website based on my mods.
Car is running great with it so I'm happy...for now ;-)

Thanks,
Rob.

If you're still have the 2 stock cats in place you should be running a stage 1 map

[Snotrocket]

Hi Shawn,


Car is running great with it so I'm happy...for now ;-)

Thanks,
Rob.

Cars generally run amazing just before they blow up......

[loki]

Cars generally run amazing just before they blow up......

Ask Shawn how he knows

[boyracer]

What's up Shawn?

[Snotrocket]

What's up Shawn?

Hey!

[boyracer]

Hey!

Hey.

Hugs & kisses

Steve.

[Snotrocket]

Rob did you read this? Flash to stage 1 until you get some exhaust work done.


If you're still have the 2 stock cats in place you should be running a stage 1 map

[robl]

A blaze of glory...I like it!
;-)

Ok, Flipping back to stage 1 until I get my DP with high flow cat.

Thanks for the info guys...could have been an expensive lesson!

Cheers,
Rob


Cars generally run amazing just before they blow up......

[Snotrocket]

A blaze of glory...I like it!
;-)

Ok, Flipping back to stage 1 until I get my DP with high flow cat.

Thanks for the info guys...could have been an expensive lesson!

Cheers,
Rob

Good plan.

Regards,
Sean

[boyracer]

Good plan.

Regards,
Sean

Shaun?

[breakfasteatre]

thanks,
Alex

[loki]

Next person to sign their post gets it

:loki2

Bunch of flagrant behaviour in the speed section

[BlueStreak]

Anybody know who I can speak to to get an H.I.B Tune?

I also went to get some H.I.B Positive stickers on my car to rep.

[Fobio]

Anybody know who I can speak to to get an H.I.B Tune?

I also went to get some H.I.B Positive stickers on my car to rep.

Noice....

[Snotrocket]

Anybody know who I can speak to to get an H.I.B Tune?

I also went to get some H.I.B Positive stickers on my car to rep.

I am starting to give people H.I.B..... Make sure to bring lots of engine "lube". You're going to need it.

[loki]

some guy with the HIV is going to key the living f**** out of your car, Dave.

[SilentJay]

Unrelated note - It seems Rotella T6 is the oil of choice. It's being advertised at ~$34 for 5L at PartSource.

[mikey32235]

just so you friends and jerks..i mean gents know im not selling the speed.

[breakfasteatre]

Ok. Now that you have made the right decision, you need to get a new motor. I am willing to help you out. I can source a brand new long block for 3k US plus shipping and duties through my mazdaspeed account. Let me know. We want healthy speeds not beat jalopies

[mikey32235]

love the offer, ive decided though im gonna just drive it as is for now, wait untill i HAVE to do it (pretty much when power is gone), then ill start the build from there. definately forged pistons, rings etc. will keep everyone posted.

[SomeGuy]

love the offer, ive decided though im gonna just drive it as is for now, wait untill i HAVE to do it (pretty much when power is gone), then ill start the build from there. definately forged pistons, rings etc. will keep everyone posted.

"Han rebuilt this bad-boy from ground up. We talkin forged pistons, bigger turbo, new rise, new crankshaft."

[mikey32235]

"Han rebuilt this bad-boy from ground up. We talkin forged pistons, bigger turbo, new rise, new crankshaft."

i like that haha ;)

[pwdunmore]

Anyone want a 3'' Custom exhaust with a resonator on it (Gen2)? I am changing my set up as soon as I order something because I need something that is quieter on cold starts... good bye long tax return money... I am willing to sell the custom set up for a good price you would just have to get someone to install it as it will have to be cut at the axel to remove but can be rewelded and installed easily.

[mikey32235]

Anyone want a 3'' Custom exhaust with a resonator on it (Gen2)? I am changing my set up as soon as I order something because I need something that is quieter on cold starts... good bye long tax return money...

even when i had a stock speed exhaust, thing was still so loud on start ups. echo'd through the whole subdivision lol.

[loki]

even when i had a stock speed exhaust, thing was still so loud on start ups. echo'd through the whole subdivision lol.

150 psi per cylinder would do that

:chuckle

[pwdunmore]

lol ohhh loki... because it's pretty much straight pipes (the resonator does very little except get rid of the rasp) it's really loud on cold starts. My stock exhaust didn't pop as much as this one does in the morning. I need a muffler and resonator to get sound I want and the shop can only fit a 2.5'' muffler instead of a 3'' so I have to look at other set ups.

[Mr Wilson]

You can avoid cold starts on the genpu.....something about hitting the gas on startup.

[Fobio]

Prosport order arrived. I will review the parts tonight. Please arrange for pick-up! =)

[pwdunmore]

Not sure how that works for pushing the has on startup but I found a solution instead of getting a whole new exhaust but it's still gonna take some work to do.

I found the same style muffler that the Magnaflow MS3 exhaust uses but sold separately as a Camaro/Firebird muffler. It still keep the 3'' piping then goes into 2x2.5'' openings so I will still have the flow I want for the few extra HP and less WGDC. We'll see how it sounds on monday when I get this all sorted out.

I should have went Cp-e eh Mr.Wilson? :P

[Mr Wilson]

Damn straight, delivered by ups of course

[fywdyl]

You can avoid cold starts on the genpu.....something about hitting the gas on startup.

That's what I do, not because of the noise, but because the car struggles with the ported IM. Push the gas pedal in like 5%-10% and then start the car, it'll rev to about 3K rpm and then drop to idle rpm. I let it warm up a little longer when I do this though.

[mikey32235]

150 psi per cylinder would do that

:chuckle

lol asshuuuuule. its 150 for 2 cyl.. get it right dude... lol

[Fobio]

That's what I do, not because of the noise, but because the car struggles with the ported IM. Push the gas pedal in like 5%-10% and then start the car, it'll rev to about 3K rpm and then drop to idle rpm. I let it warm up a little longer when I do this though.

May also be a by-product of TB-coolant bypass?

[pwdunmore]

I am going to have to try it today after work if my car gets cold enough after sitting this afternoon, if not I will try it tomorrow morning. If it keeps it quiet through the week I am good. After thinking about it for a while I need to have a muffler to pass inspections/emissions down the road so getting a muffler put on now just saves me time later on. So it's not a complete loss, probably spent less money than a cobb exhaust still lol...

Thanks for all the tips guys :)

PS anyone have the hole punch for doing the Washer Method install for meth nozzles?

[loki]

I am going to have to try it today after work if my car gets cold enough after sitting this afternoon, if not I will try it tomorrow morning. If it keeps it quiet through the week I am good. After thinking about it for a while I need to have a muffler to pass inspections/emissions down the road so getting a muffler put on now just saves me time later on. So it's not a complete loss, probably spent less money than a cobb exhaust still lol...

Thanks for all the tips guys :)

PS anyone have the hole punch for doing the Washer Method install for meth nozzles?

isn't your car a 2011? making it due for inspection in 2018?

[loki]

also muffler and/or resonator does nothing for omissions

[pwdunmore]

Ya it looks like there are no emissions regulations about a muffler but safety/law states you need to have an operational muffler on the exhaust, so straight pipes with a resonator is not quite meeting that requirement.

Just looking out for the future, gonna have to do it sooner or later so why not now. I wouldn't be able to sell the car without one either or have a really hard time finding a buyer.

[standsideways]

No emissions test facility is going to get under your car and check the exhaust system out, ESPECIALLY with the new system being in place, check the OBD2 for emissions codes. Done...IIRC it does not roll on the dyne anymore..


And they cant say "thats a resonator not a muffler" so it doesnt matter.

[pwdunmore]

Safety Inspection check for it?

[fywdyl]

May also be a by-product of TB-coolant bypass?

Could be, but I did both at the same time, so I have no way of telling which one is the culprit.


I am going to have to try it today after work if my car gets cold enough after sitting this afternoon, if not I will try it tomorrow morning. If it keeps it quiet through the week I am good. After thinking about it for a while I need to have a muffler to pass inspections/emissions down the road so getting a muffler put on now just saves me time later on. So it's not a complete loss, probably spent less money than a cobb exhaust still lol...

Thanks for all the tips guys :)

PS anyone have the hole punch for doing the Washer Method install for meth nozzles?

Use a drill bit for that. I also have a drill bit to tap the WWF tank (Simon).

[Mr Wilson]

^^^ Are you still noticing initial idle issues with the warmer weather we are having? Granted as much as these cars are the same, they each have so much of their own character, I haven't noticed any issues after the coolant bypass.

[Snotrocket]

No emissions test facility is going to get under your car and check the exhaust system out, ESPECIALLY with the new system being in place, check the OBD2 for emissions codes. Done...IIRC it does not roll on the dyne anymore..


And they cant say "thats a resonator not a muffler" so it doesnt matter.

If there are no codes (hence the AP clears them) will my car pass without cats?

[standsideways]

Yep^

But i am not 100% sure the system wont somehow detect the AP.

Im not a drive clean inspector anymore, dont know the new stuff exactly, or what has changed hardware/software wise over the old dinosaur dial up stuff.

[trinxified]

Hi guys,

I'm a new 2013 black MS3 owner. I love the car so far but got a few questions.

I noticed in some pics that there is a blue footwell lighting, similar to the ones that are lit up by the gearbox and door handles. How come my car doesn't have that on the footwell? Is that a removed feature for the 2013 model year or it's an added accessory that you need to buy?

[Snotrocket]

Hi guys,

I'm a new 2013 black MS3 owner. I love the car so far but got a few questions.

I noticed in some pics that there is a blue footwell lighting, similar to the ones that are lit up by the gearbox and door handles. How come my car doesn't have that on the footwell? Is that a removed feature for the 2013 model year or it's an added accessory that you need to buy?

Comes with the rice package. Did you get it?

[pwdunmore]

No cats should work as along as the system shows as ready, so having one of those O2 stems might do the trick.

The footwell lighting was taken out of later model MS3's(2012 and on, I think... Mine didn't come with it either so I am assuming 2012's maybe 2011's too). You can have them put in still but you need to buy the kit or DIY.


OHHH and I tried to cold start with the gas pedal down a tiny bit... worked like a charm! I wonder why that over rides the normal cold start process the MS3 uses. All I got was one loud pop this morning and then the rpms settled. Thanks for the tip guys :)

[CelestSpeed3]

Foot well lighting was only on early 2010's. More specifically I believe only cars with an '09 build date.

[loki]

First post on tm3 and in speed section is about footwell lighting

[S.F.W.]

First post on tm3 and in speed section is about footwell lighting

Still relevant

[boyracer]

Use a drill bit for that. I also have a drill bit to tap the WWF tank (Simon).


I'll need to borrow that.

[trinxified]

Comes with the rice package. Did you get it?

What rice package? :(


The footwell lighting was taken out of later model MS3's(2012 and on, I think... Mine didn't come with it either so I am assuming 2012's maybe 2011's too). You can have them put in still but you need to buy the kit or DIY.

Thanks that's what I thought too. I guess the "rice" package is that overpriced interior lighting kit Mazda is selling. What does that contain other than footwell lighting?


Foot well lighting was only on early 2010's. More specifically I believe only cars with an '09 build date.

What's the reason behind removing features like this? Cheaped out?


First post on tm3 and in speed section is about footwell lighting

Nothing else to complain about at the moment. :P

[pwdunmore]

They removed a lot of the little things like the lights, scuff plates in the door james and a fancy oil cap for saving money I suppose... this way people have to pay for all the nice little accessories. Kinda sucks but whatever, you don't really notice it much when you are flooring it with a big smile on your face lol.

[trinxified]

They removed a lot of the little things like the lights, scuff plates in the door james and a fancy oil cap for saving money I suppose... this way people have to pay for all the nice little accessories. Kinda sucks but whatever, you don't really notice it much when you are flooring it with a big smile on your face lol.

Yup just saw those things you mentioned on the Options & Accessories page as a add-on from the website.

I wonder how many things were removed. It's too bad because later models should be getting more things on it, especially how 2013 is the final model year for this current generation. Doesn't seem fair and I believe the MSRP is higher for 2013 model too.

[Fack_Dude]

Yup just saw those things you mentioned on the Options & Accessories page as a add-on from the website.

I wonder how many things were removed. It's too bad because later models should be getting more things on it, especially how 2013 is the final model year for this current generation. Doesn't seem fair and I believe the MSRP is higher for 2013 model too.

Who cares. At the end of the day, you will have a rust bucket worth very little.

[Mr Wilson]

hahaha so positive

[Fack_Dude]

hahaha so positive

Just gotta put things in perspective.....lol

[boyracer]

Who cares. At the end of the day, you will have a rust bucket worth very little.


hahaha so positive


Just gotta put things in perspective.....lol

That's why we love you

[CelestSpeed3]

They included it in the early 2010's because it was part of the marketing release. The only option I had available was colour.

That being said, I love the 2013 interior and exterior changes. I'll trade you door sills and footwell lighting for that nice radio, blind spot indicator, and rear bumper.

[trinxified]

They included it in the early 2010's because it was part of the marketing release. The only option I had available was colour.

That being said, I love the 2013 interior and exterior changes. I'll trade you door sills and footwell lighting for that nice radio, blind spot indicator, and rear bumper.

There is still a door sill on the 2013... Unless it was different/better before? Blind spot indicator is only tech package, which I don't have lol. And you mean the Bose radio?

[CelestSpeed3]

That nice big screen radio the 2013's get.

[Fack_Dude]

anyone going to the ian law school this weekend?

[standsideways]

anyone going to the ian law school this weekend?

Not my cup o tea.

EDIT: ill be at MIR watching racing :)

[CelestSpeed3]

You'd rather be watching racing then driving?

You feeling okay?


Edit: Most of the Mspeed crew will be at ILR.

[Nino]

Just about shat my pants today.. car went POOF! While wot in 2nd gear on a back road on the outskirts of town. I limped my way home to find out a coupler/clamp blew on my fmic hotpipe.

Not happy at all.

[thanu31]

My car is being all weird :-( car keeps dieing in a few hours and got these codes
http://img.tapatalk.com/d/13/05/14/7unytamy.jpg

[loki]

Just about shat my pants today.. car went POOF! While wot in 2nd gear on a back road on the outskirts of town. I limped my way home to find out a coupler/clamp blew on my fmic hotpipe.

Not happy at all.

You should be happy, nothing is wrong with your car

[Snotrocket]

Just about shat my pants today.. car went POOF! While wot in 2nd gear on a back road on the outskirts of town. I limped my way home to find out a coupler/clamp blew on my fmic hotpipe.

Not happy at all.

Wtf.... Thats your issue? Christ, i kill someone to only have that to worry about with my car right now.

[loki]

Wtf.... Thats your issue? Christ, i kill someone to only have that to worry about with my car right now.

Newbs

[Jsquared]

About to take the speed down to Tennessee to run tail of the dragon. Leaving Thursday morning. Taking the car in for a service inspection tomorrow morning. Doing an oil change and having it inspected for about 25 other things that they suggested.

Is there anything I should ask them to check outside of the standard oil, coolant levels, battery and suspension?

Thanks guys!

[Fack_Dude]

Just about shat my pants today.. car went POOF! While wot in 2nd gear on a back road on the outskirts of town. I limped my way home to find out a coupler/clamp blew on my fmic hotpipe.

Not happy at all.

Well then don't mod the car.

[mikey32235]

Well then don't mod the car.

lol, dont be a mikey. tighten your clamps, hairspray!

[pwdunmore]

lol, dont be a mikey. tighten your clamps, hairspray!

Lmao... love the reference to yourself

[mikey32235]

Lmao... love the reference to yourself

i just had to haha

[Nino]

Shoulda bought a neon or a caliber srt4

[loki]

Shoulda bought a neon or a caliber srt4

Why?

[mikey32235]

Shoulda bought a neon or a caliber srt4

why would u want that piece of sheit?

[breakfasteatre]

Shoulda bought a neon or a caliber srt4

They both come with FMIC stock.

[Nino]

Why?


why would u want that piece of sheit?


They both come with FMIC stock.

Lol was gonna say this but **** that noise. Im just trying to pull some legs here.

[Elusivellama]

http://i853.photobucket.com/albums/ab96/Elusivellama/4F87546E-B3AE-4EA5-8A0B-84D74488381F-1205-000001C5BCF27C9F_zpsf16dfbd4.jpg

JBR sway bar. Good bar.

Shitty hardware. Anyone know where I can get a good set of the bushing clamps that aren't made out of ****ing pop can foil? Irritated to say the least.

[loki]

Ewe so elusive

[SomeGuy]

Oooh that's rough.

The ones that came with my corksport are holding up decently...had the collars replaced due to rusting out in a single winter (second set held up way better). Could just see if they'd sell you a set?

[Elusivellama]

Yeah JBR does sell a set, but tomorrow I'll go look at a local Brafasco/Fastenal or Spaenaur for a 1.25" clamping collar that's made out of a thicker gauge stainless steel, or something.

[CelestSpeed3]

http://www.hotchkis.net/heavy_duty_billet_sway_bar_bushing_bracket_w_138_b ushing.html


I didn't use the retaining collars on my car.

[pwdunmore]

Anyone been to Hot Rod Scott's for exhaust work?

Just got my muffler in the mail so I want to get it welded in, I ideally didn't want to have to go back to the other shop where I got the 3'' Custom Exhaust so I am looking around Mississauga/Etobicoke.

[mikey32235]

never heard of them, for all my exhaust jobs if i cant do it myself i go to noysboys

[S.F.W.]

Anyone been to Hot Rod Scott's for exhaust work?

Just got my muffler in the mail so I want to get it welded in, I ideally didn't want to have to go back to the other shop where I got the 3'' Custom Exhaust so I am looking around Mississauga/Etobicoke.

Never been to then myself, but many of the regular 3 guys I have, and work is always well regarded.

[Mr Wilson]

They always have some pretty nice vehicles they are working on when evere I drive by.

[BlueStreak]

Anyone been to Hot Rod Scott's for exhaust work?

Just got my muffler in the mail so I want to get it welded in, I ideally didn't want to have to go back to the other shop where I got the 3'' Custom Exhaust so I am looking around Mississauga/Etobicoke.

Yep. They did some mega custom mid pipe work on my car and it looks and works great.

They ain't cheap tho. Damn near fell off my chair when the bill came.

[pwdunmore]

Yep. They did some mega custom mid pipe work on my car and it looks and works great.

They ain't cheap tho. Damn near fell off my chair when the bill came.

Lol ya, that is kind of expected... I have the muffler in my trunk so they just have to install it. Went over at lunch yesterday and Scott said it would be around $150 to install which isn't terrible.

Considering going FMIC now but since I am going to be a Meth addict I am not sure if it's worth it or not... tax return money has me tempted lol...

[mikey32235]

Lol ya, that is kind of expected... I have the muffler in my trunk so they just have to install it. Went over at lunch yesterday and Scott said it would be around $150 to install which isn't terrible.

Considering going FMIC now but since I am going to be a Meth addict I am not sure if it's worth it or not... tax return money has me tempted lol...

do the fmic, power after tuning with the ap was incredible. i could only imagine what the meth would add to that. had to cancel my meth order since i ran into my own problems with my car. gotta order soon pistons, rods etc.. the whole deal!

[pwdunmore]

do the fmic, power after tuning with the ap was incredible. i could only imagine what the meth would add to that. had to cancel my meth order since i ran into my own problems with my car. gotta order soon pistons, rods etc.. the whole deal!

Just not sure the FMIC is worth it since I have the Cp-e TMIC already which flows great, it just gets heat soaked after a while but I would think the meth would cool things down a fair bit anyways.

Just curious if anyone was ever made the switch from TMIC to FMIC with methanol injection and it made a difference with the stock turbo.

I was thinking about getting the CX racing FMIC piping kit with a TR6 intercooler which wouldn't break the bank then selling my Cp-e TMIC which would make up for some of the difference in cash.

The thing is with your build is that you need that FMIC if you are going to produce all the extra power and heat, it would heat soak a TMIC in no time without meth.

[mikey32235]

thats the same fmic i have, and its great! definately the tmic makes a difference once u go aftermarket but the fmic is even better. cx makes it at a reasonable price too and if u sell ur tmic, it wont cost you so much in the end to do the fmic uprade.

[loki]

What is going on here

How will meth help with heat soak?

The CPe tmic cools off almost immediately once the air starts to move

[pwdunmore]

What is going on here

How will meth help with heat soak?

The CPe tmic cools off almost immediately once the air starts to move

It cools off to an extent but it still remains warm, even when moving the TMIC will be warmer from the heat of the exhaust gases so even with Meth the charge will still be a little heated up compared to a FMIC.

I was just curious where the tipping point for BAT's, the cooler the charge the more dense so it makes more power but at what point does that temperature not matter anymore because the air is already as dense as it can get (similar with all fluids).

From what I have read of MSF: TMIC + Meth ~ ambient air temperature so FMIC + Meth ~ cooler then ambient?

I guess I will ask the tooners on MSF to see if benefits outweigh the cost.

[loki]

You can't pressurize air to that extent and have it cooler than ambient. Even with meth.

[pwdunmore]

You can't pressurize air to that extent and have it cooler than ambient. Even with meth.

Ahhh true, makes sense... so what's your oppinion on it loki? Just do the meth with my TMIC?

[loki]

Ahhh true, makes sense... so what's your oppinion on it loki? Just do the meth with my TMIC?

Yeh that's what I would do if I was you

I wouldn't even do meth unless you were planning to have it tuned and really push the limits of the K04

[loki]

Phil doesn't have meth and he's pushing a cool 300 whp

[pwdunmore]

I was doing it for the cleaning plus a little power, I will get a tune as soon as all of my stuff is installed. Just waiting on the JBR order. Right now I am using a stratified OTS tune and it's pretty awesome but I know mspeed does good work too so I'm up in the air right now.

[loki]

I was doing it for the cleaning plus a little power, I will get a tune as soon as all of my stuff is installed. Just waiting on the JBR order. Right now I am using a stratified OTS tune and it's pretty awesome but I know mspeed does good work too so I'm up in the air right now.

Won't add any power with any OTS tune

Car needs to be specifically dialed in

[Booostin]

Hot Rod Scotts does good work but they are a rip. Go to JPG Exhaust in Oakville.

[zzz3]

Hot Rod Scotts does good work but they are a rip. Go to JPG Exhaust in Oakville.

Yup. JPG actually stands for 'just praise god' lol.

[pwdunmore]

Won't add any power with any OTS tune

Car needs to be specifically dialed in

I know lol... I am not a noob at this point. I just like to hear what people have to say about the mods they have or have done. (That being the FMIC's)

One thing I can definately comment on is the OTS stratified maps are better than the OTS cobb maps, the butt dyno can feel it.

And I will look into JPG Exhaust, thanks guys.

[fywdyl]

I know a guy running BT w/ TMIC and meth and is making decent power.

PS - You have more options with the TMIC when it comes to tapping the nozzle. With the FMIC, you basically have to weld a bung.

[Snotrocket]

I know a guy running BT w/ TMIC and meth and is making decent power.

PS - You have more options with the TMIC when it comes to tapping the nozzle. With the FMIC, you basically have to weld a bung.

Is he a cool dude?

[boyracer]

I know a guy running BT w/ TMIC and meth and is making decent power.

PS - You have more options with the TMIC when it comes to tapping the nozzle. With the FMIC, you basically have to weld a bung.


Is he a cool dude?

I hear he's really really smart.

[fywdyl]

Is he a cool dude?


I hear he's really really smart.

He also likes the company of gentlemen.

[loki]

He also likes the company of gentlemen.

but doesn't like them to be gentle

[mikey32235]

This weekend is the Georgian College Auto show, i will be representing Volvo Newmarket, if anyone is gonna be down there, come by! gonna be an awesome weekend.

[pwdunmore]

245/45/17 tire with a 45+ 17/9 rim, will I need a roll?

I researched a bit on msf but wanted to ask TM3 too, my buddy works at a tire shop so he was gonna hook me up :)

[SomeGuy]

Corksport Group Buy if any of you sluts want something:
http://www.torontomazda3.ca/forum/showthread.php?71237-GB-Corksport-KW-Region

[loki]

Corksport Group Buy if any of you sluts want something:
http://www.torontomazda3.ca/forum/showthread.php?71237-GB-Corksport-KW-Region

I hear their coilovers are amazing.....

[SomeGuy]

I hear their coilovers are amazing.....

http://www.troll.me/images/futurama-fry/cant-tell-if-sincere-or-just-being-sarcastic.jpg

[2zoom]

http://www.troll.me/images/futurama-fry/cant-tell-if-sincere-or-just-being-sarcastic.jpg


It's Loki need you ask...

[SilentJay]

http://cdn.memegenerator.net/instances/400x/38448934.jpg

[loki]

Enjoy

http://www.mazdaspeedforums.org/forum/f500/corksport-146959/

[SomeGuy]

Enjoy

http://www.mazdaspeedforums.org/forum/f500/corksport-146959/

Interesting...sucky for corksport not to fully test them at all adjustments and sucky for Paul having to deal with that shit. I'm sure the coilovers aren't complete garbage but obviously they aren't perfect.

[Nino]

Someone please recommend me a solution permanently fix my w-h-h-h-h-h-h-h-h-h-h-h-h-eel hop-p-p-p-p-p-p-p-p-p-p-p-p-p-p problem.

I'm assuming just a RMM won't cut it.

I hopped so hard at the track today that my change bounced and flew all over the place, as well as the top of my air freshener.

[Kiyomi]

Someone please recommend me a solution permanently fix my w-h-h-h-h-h-h-h-h-h-h-h-h-eel hop-p-p-p-p-p-p-p-p-p-p-p-p-p-p problem.

I'm assuming just a RMM won't cut it.

I hopped so hard at the track today that my change bounced and flew all over the place, as well as the top of my air freshener.

driver mod.

lol jst kdn. try and feather the clutch and not launch as hard as you can. keep on dsc?

[Nino]

driver mod.

lol jst kdn. try and feather the clutch and not launch as hard as you can. keep on dsc?


I was at the drag strip.. Tried everything.. DSC on was a disaster. Feathering the clutch helped a bit but I'd hop at the end of 1st and hop again shifting into 2nd.

Best I could run was a 13.7(Full stage 2 OTS) with abysmal 60' times of 2.2-2.4. I was trapping anywhere from 104-106mph.

[Kiyomi]

I was at the drag strip.. Tried everything.. DSC on was a disaster. Feathering the clutch helped a bit but I'd hop at the end of 1st and hop again shifting into 2nd.

Best I could run was a 13.7(Full stage 2 OTS) with abysmal 60' times of 2.2-2.4. I was trapping anywhere from 104-106mph.

thats still pretty decent. what tire setup u running?

[SomeGuy]

Wheel hop is just going to be replaced with wheel spin if you go with a full set of mounts.
Better rubber will help if you can keep them from letting go.
Ditch the OTS tune with something that is more linear and enable LC and FFS.

[Nino]

thats still pretty decent. what tire setup u running?

225/40/18 Hankook ventus V12 on XXR 527 wheels.


Wheel hop is just going to be replaced with wheel spin if you go with a full set of mounts.
Better rubber will help if you can keep them from letting go.
Ditch the OTS tune with something that is more linear and enable LC and FFS.

I was running at a 2900RPM LC the whole time and FFS at 6700RPM.. My last few runs I switched to map without LC and FFC enabled.. Still ran a 13.7

I'd honestly rather have wheelspin than the violent wheel hop I was experiencing today... It's weird, the wheel hop came along with my DP.. Never experienced wheel hop before the DP.

I'll definitely need a good tune..

I thought I'd run better times than 13.7 with my mods (SRI, TIH, TBE, FMIC, HPFP, OTS stage 2). Looks like this is where the drivetrain/suspension mods come into play.

[SomeGuy]

FFS at 6700RPM is too high...that's essentially redline, you want it closer to where the revs end up after the shift.

With the downpipe and going to the stage 2 maps you gain a substantial amount of power...wheel spin in 2nd is more possible.

Interestingly enough I'm around the same level of mods (see sig) and so long as the surface isn't wet, I don't get wheel hop at all even though I can easily break loose in 2nd from a roll and occasionally see the traction control light flash in 3rd on dry pave. Mind you this isn't on a drag strip but this is without any suspension mods that will help and just a soft RMM and good tires (even the stock dunlops I didn't have issues with wheel hop though).

[Nino]

Interesting.. Is there any reason as to why you went with a soft RMM? How harsh is it? I'm on stock mounts due to long commutes but I'm really considering upgrading.

I have a set of coilovers sitting in the garage which will probably help out.

[SomeGuy]

It's just a 60 duro but still WAY better than the stock RMM. I went with the softer one because it's my daily driver and didn't want it to be too annoying. After a week or two you don't even notice the vibes or they're basically all gone. Definitely worth while and given you're already stage 2 your exhaust setup is far more annoying than the RMM would ever be. The cp-e stage 2 mount is supposed to be even better.

Stocker:
https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-prn2/247524_550303691723_3032029_n.jpg
Cp-e Stage 1 60 duro:
https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-ash4/225300_550147953823_7901902_n.jpg

[Fack_Dude]

OP, replace motor mounts with stiffer mounts and buy good r compound tires.

[Nino]

Great info in here. Thanks for the help!

[MarineMazda]

Great info in here. Thanks for the help!

You could always sell MS3 and Buy MS6 and Wheel hop, wheel spin, and torque steer won't be an issue. Just a thought :P

[Snotrocket]

You could always sell MS3 and Buy MS6 and Wheel hop, wheel spin, and torque steer won't be an issue. Just a thought :P

He wants to get rid of wheel hop not turn gay..... ;)

[Nino]

Tbh I started to wish I got an ms6 instead about a month after I got the 3.. However it seems like the 6 has more problems than the 3..


either way fwd sucks lol.

[MarineMazda]

He wants to get rid of wheel hop not turn gay..... ;)

Gay... you want to talk about gay check this out!

http://i61.photobucket.com/albums/h58/Mach1_photos/944183_10151451037690172_1458011049_n_zps775b14d6. jpg (http://s61.photobucket.com/user/Mach1_photos/media/944183_10151451037690172_1458011049_n_zps775b14d6. jpg.html)

Now thats GAY!!!

[MarineMazda]

Tbh I started to wish I got an ms6 instead about a month after I got the 3.. However it seems like the 6 has more problems than the 3..


either way fwd sucks lol.

To be honest the 6 and the 3 have the same amount of problems.... Ask SnotRocket his 3 has the same issue and my 6 LMAO

[Snotrocket]

Gay... you want to talk about gay check this out!

http://i61.photobucket.com/albums/h58/Mach1_photos/944183_10151451037690172_1458011049_n_zps775b14d6. jpg (http://s61.photobucket.com/user/Mach1_photos/media/944183_10151451037690172_1458011049_n_zps775b14d6. jpg.html)

Now thats GAY!!!

wanna go out sometime?

Edit: Look at that chick checking it out !

Texting her friends to come sleep with me

[Mr Wilson]

Mike...you gotta peg leg that bish down the drag strip against doubleflusher.

[Snotrocket]

Mike...you gotta peg leg that bish down the drag strip against doubleflusher.

That would be a tight race!

[Booostin]

5.0s are bad ass.

[mikey32235]

agreed

[BlueStreak]

Doesn't that qualify as a 5.slow?

[Snotrocket]

Doesn't that qualify as a 5.slow?

Who's the funny guy? Don't quit your day job.....

[SomeGuy]

WOW

http://www.corksport.com/corksport-mazdaspeed-3-big-brake-caliper-kit.html

'nuff said

[mikey32235]

jeez, that looks sexy !

[Kiyomi]

WOW

http://www.corksport.com/corksport-mazdaspeed-3-big-brake-caliper-kit.html

'nuff said

:drool

[zzz3]

WOW

http://www.corksport.com/corksport-mazdaspeed-3-big-brake-caliper-kit.html

'nuff said

If someone buys this I will buy your stock speed calipers to help offset costs! $200~ cash...

[pwdunmore]

Hey guys, anyone know a good shop in the west end that does alignments? I ideally didn't want to pay dealership rates but I know worst case scenario I get it done when I do my oil change at budd's...

Just got on my new tires and rims so I want to make sure they wear correctly.

[S.F.W.]

How far west ? Altech is good .

[pwdunmore]

Ideally close to mississauga, oakville or etobicoke

[Mr Wilson]

Second Altech.

[pwdunmore]

cool, thanks guys. I will give them a call on tuesday morning to see how much they charge and when they can getter done.

[Polish_Eagle]

Shit, I just go to Canadian Tire and give them my custom specs and they set the car up that way. They are fast and do exactly what I need.

[rzapata]

Shit, I just go to Canadian Tire and give them my custom specs and they set the car up that way. They are fast and do exactly what I need.

Good for you. Some of them do mess up though. I know a couple of people who had bad experiences (loose lug nuts, not tightened)...

[loki]

No Canadian Tire for my car

[loki]

Will have turbosmart dual port bpv/bov up for sale shortly once my new valve comes in


Great upgrade over stock. Bling bling.

[DLYDRVN]

I'm taking zzz3 up on his offer. Perhaps the first guinea pig for the callipers?

[Polish_Eagle]

Good for you. Some of them do mess up though. I know a couple of people who had bad experiences (loose lug nuts, not tightened)...

LOL, someone's angry. Loose lugs can happen at any shop, saying all Canadian Tire shops are shit is just ignorant.